Specification & Accessory

GL7000 specifications

Item Description
Model number GL7000
Number of module Attached to up to 10 modules (*1)
Number of input channels Max. 112 channels in 1 of GL7000
External Input/Output signals (*2) Input Start/Stop, External trigger, External sampling, Auto balance (*3)
Signal type: Contact (relay), Open collector, Voltage
Output Trigger, Busy (*3), Alarm (10 channels) (*4)
Signal type: Open collector (pulled-up by resistor 10 kΩ)
Trigger, Alarm function Trigger action Start or stop capturing data by the trigger
Trigger repeat Enabled (ON): Automatically re-armed for the next data capture function
Disabled (OFF): Data capture is completed in a single trigger
(Hold off repeat action in specified period: Previous start to next start, previous stop to next start)
Trigger source Start: Off, Measured signal, Alarm, External signal, Clock, Week or Time
Stop: Off, Measured signal, Alarm, External signal, Clock, Week or Time
Trigger determination conditions for measured signal Combination: OR or AND condition at the level of signal or edge of signal
Analog: Higher/Rising, Lower/Falling, Window-in, Window-out
Logic (*5): Higher/Rising, Lower/Falling
Pulse (*5): Higher/Rising, Lower/Falling, Window-in, Window-out
Alarm determination condition (*6) Combination: OR or AND condition at the level of signal or edge of signal
Analog: Higher/Rising, Lower/Falling, Window-in, Window-out
Logic (*5): Higher/Rising, Lower/Falling
Pulse (*5): Higher/Rising, Lower/Falling, Window-in, Window-out
Alarm output 10 channels
Pre-trigger (*7) Number of data before trigger: Up to specified number of captured data
Calculation function Between channels Addition, Subtraction, Multiplication and Division for two analog inputs (Sampling speed is limited up to 10 Samples/s (100 ms interval). Available arithmetic element and the output destination is the analog input channel 1 to 100.)
Statistical Select two calculations from Average, Peak, Max., Min. in real time and replay (*8)
Move function of the display range Beginning, center or end of the data, Trigger point, Specific time (absolute, relative), Call cursor
Search function Search for analog signal levels, logic signal pattern, pulse signal levels or alarm point in captured data
Annotation function Comment can be set in each channel (up to 31 alphanumeric characters)
Message / Marker Functions Message: The registered messages or entered message is able to be recorded for any timing. Up to 8 messages can be pre-registered.
Marker: Marker is able to record for occurring alarm or power failure.
Resume Resume automatically in the same condition after power is recovered as when the power failure occurred during data capture. (*9)
FFT analysis function
(Firmware ver. 1.20 or later)
Analyzing frequency range 0.08, 0.2, 0.4, 0.8, 1.6, 2, 3.2, 4, 8, 20, 40, 80, 200, 400, 800 Hz, 2, 4, 8, 20, 40, 80, 200, 400 kHz
Number of points 500, 1000, 2000, 4000, 10000
Window function Rectangular, Hanning, Hamming, Blackman, Flat-top, Exponential
Averaging Summation average, Exponential average, Peak hold
Channels 4 channels
Functions Y-T, Linear, Power, PSD, Cross, Transfer function, Coherence, COP
Display mode Single display, Dual display, Nyquist
Interface to PC Ethernet (10 BASE-T/100 BASE-TX), USB 2.0 (High speed)
Network function WEB server, FTP server, FTP client, NTP client, DHCP client
USB drive mode Emulate the USB memory device (*10)
Storage device Built-in RAM (2 million samples, built-in amplifier module),
Flash memory (4 GB, built-in the main module) (*12)
External (*11) SD card (Support SDHC, up to 32GB) slot, SSD (Approx. 128GB (*12))
The file for capturing data is limited up to 4GB. (*13)
Data saving function Sampling speed (interval) 1 MS/S(1 million samples per second) to 1S/h (1 sample per hour), and synchronized with external sampling signal
(Interval: 1, 2, 5, 10, 20, 50, 100, 200, 500 µs, 1, 2, 5, 10, 20, 50, 100, 200, 500 ms, 1, 2, 5, 10, 20, 30, 1, 2, 5, 10, 20, 30 min, 1 hur)
* The maximum sapling speed (minimum sampling interval) is different depending on the type of module.
* Sampling can be set up to the fastest speed among multiple type connected modules. If the set sampling speed exceeds the fastest speed on module, signal will be sampled and updated at the highest speed of its module and the previous data will be used until the data is updated.
* The maximum sampling speed (minimum sampling interval) varies depending on the specified recording destination.
Built-in RAM: up to 1 MS/s (1 µs interval)
SSD module: up to 500 kS/s (2 µs interval) at 1 or 2 modules installed, up to 200 kS/s (5 µs interval) at 3 or 4 modules installed, up to 1 kS/s (1 ms interval) at 5 or 10 modules installed
Built-in Flash memory: up to 1 MS/s (1 µs interval)
External SD Flash memory: up to 1 kS/s (1 ms interval)
Captured data (*11) Built-in RAM, Built-in Flash, SD memory card, SSD (Data is saved directly to it.)
Data in built-in RAM Specified number of data up 2 million samples in increments of 1
Auto save (*11) Available for the built-in RAM
Enabled (ON): Data in the RAM is saved automatically to the built-in Flash, SD memory card, SSD
Disabled (OFF): Data in the RAM is not maintained after power is turned off
Capturing mode (*11) Mode: Off, Normal, Ring, Relay
Ring (*14): Saved most recent data (Number of capturing data: 1000 to 2000000 points, Destination of data: Built-in RAM, Built-in Flash, SD memory card, SSD)
Relay(*13)(*15): Saved data to multiple file without losing data until capturing data is stopped (Destination of data: Built-in Flash, SD memory card, SSD)
During data capture (*17) Displaying information in two windows, Hot-swapping the SD memory card, Saving data in between cursors.
Backup (*11) Backup interval: Off, 1, 2, 6, 12, 24 hrs.
Data destination: SD memory card, SSD, FTP server
Data destination for backup cannot be specified to the same storage for destination of capturing data.
Dual sampling function (*18) It enables to record signal with two sampling speed. While the signal is recorded with low speed sampling for long term recording, the transient part is recorded with high speed sampling after the trigger occurs.
Current (low-speed) sampling
Recording mediaFBuilt-in flash memory or SD card
Sampling intervalF1, 2, 5, 10, 20, 50, 100, 125, 200, 250, 500ms, 1, 2, 5, 10, 20, 30s, 1, 2, 5, 10, 20, 30min, 1h
Trigger timer feature: Starting time, Stopping time, Repeat recording
Event (high-speed) sampling
Recording mediaFBuilt-in RAM or SSD (optional)
Sampling intervalF 1, 2, 5, 10, 20, 50, 100, 200, 500us
Engineering Scale function Measured value can be converted to the engineering unit
Analog voltage: Converts by four reference points (gain, offset)
Temperature: Converts by two reference points (offset)
Pulse count: Converts by two reference points (gain)
Synchronization between units Start and Trigger (*16)
Accuracy of clock (at 23°C) ±0.002% (Monthly deviation approx. 50 sec.)
Operating environment 0 to 40°C, 5 to 85% RH (non condensed)
Power source 100 to 240 V AC, 50 to 60Hz
Power consumption 110VA
Standard accessories Quick guide, CD-ROM, AC power cable
External dimensions (W x D x H) Main module: Approx. 193 x 141 x 160 mm (Excluding Projection),
Alarm output terminal: Approx. 30 x 136 x 145 mm (Excluding projection)
Weight Main module: Approx. 2.2 kg, Alarm output terminal: Approx. 350 g
(*1)
Excluding the function module as the Display module or SSD module. In case of the DC Strain module (GL7-DCB): up to 8 modules. In case of the Logic/Pulse module (GL7-L/P): input mode is selected in the logic or pulse for each module, up to 7 modules when the module is used in the logic mode, up to 2 modules when the module is used in the pulse mode.
(*2)
The Input/Output cable (B-513) is required for connecting the signal. The Auto balance signal input and the Busy signal output are available in the DC Strain module (GL7-DCB).
(*3)
It is available on the DC strain (GL7DCB) module.
(*4)
The alarm signals are outputted on the terminal block attached to the main module as standard accessory.
(*5)
It is available on the Logic/Pulse (GL7-L/P) module.
(*6)
Method of detection
Volt./Temp. module:
The alarm is detected every 5 seconds when the sampling interval is longer than 5 seconds and reported. The alarm is detected in the sampling interval when the sampling interval is shorter than 5 seconds and reported.
Other modules:
The alarm is detected every 1 ms when the sampling interval is shorter than 1ms. The alarm is detected in the sampling interval when the sampling interval is set between 2 ms to 5 seconds and reported. The alarm is detected every 5 seconds when the sampling interval is longer than 5 seconds and reported.
(*7)
It is available when the captured data is saved to the built-in RAM. The pre-trigger function may not available in combination with the trigger settings.
(*8)
The result of real time calculation is displayed in the digital display mode. Available sampling speed is the 10 samples/s (100 ms interval).
(*9)
When the captured data destination is set to the built-in-RAM, the captured data is not maintained after a power failure is occurred. When destination is set to the built-in Flash or the SD memory card, it may have a problem by a power failure if it is being accessed to write data. If the memory device is not damaged, the closed data file is maintained. The file is closed every minute while data is being captured. This function is not available when the FFT mode or the Voltage Output module (GL7-DCO) is used.
(*10)
The USB drive mode is started by setting of the switch on the main module. It can be also started when the power is turned on while pressing the START/STOP key on the display module.
(*11)
The SD memory card is not included as a standard accessory. Compatible SD card type: SD, SDHC Speed class 4 or faster. The SSD module (GL7-SSD) is an option.
(*12)
Capacity of memory device may be smaller depending on time of production.
(*13)
The file for recording data is limited up to 4GB on firmware version 2.0 or later, 2GB on firmware version 1.6 or before.
(*14)
The capacity for saving the data is set to one third of available memory when the captured data destination is set to a device other than the built-in-RAM. Available sampling speed is up to 10 samples/s (100ms interval).
(*15)
When the captured data destination is set to the built-in Flash or the SD memory card, sampling speed is limited up to 100 samples/s (10 ms interval). In case of using the SSD module (GL7-SSD), sampling speed in limited up to 50 thousand samples/s (20 µs interval) when 1 or 2 modules are attached.
(*16)
The Sync cable (B-559) is required when this function is used. The GL-Connection software is required when the synchronizing function is used.
(*17)
This function is able to be available when sampling speed is set up to 10 samples/s (100 ms interval).
(*18)
Both slow and high speed sampling can only be recorded in GBD format.
When event (high-speed) capturing destination is extended SSD unit, it takes a few seconds for event capturing.
Following actions are not available:
- External sampling
- Ring / Relay recording
- Back up feature
- Dual screen feature (playback while recording)
- XY / FFT function
- Synchronization operating with multiple GL7000
- Configuring with only Voltage module (GL7-V) or Voltage/Temperature module (GL7-M)

Software specifications

Item Description
Model name GL-Connection
Supported OS Windows 10 / 8.1/ 8/ 7 (32/64-bit edition)
Functions Control GL7000, Real-time data capture, Replay data, Data format conversion
Controlled unit Up to 10 units with GL7000, GL2000, GL980, GL900, GL840, GL820, GL240, GL220
GL7000 only: max. 1120 channels
Mixing with GL series: max. 2000 channels
GL7000 Settings control Input settings, Memory settings, Trigger and Alarm settings, Other settings
Captured data (*19) * Built-in RAM (Binary format), Built-in Flash memory (Binary, CSV format), SD memory card (Binary, CSV format), SSD (Binary, CSV format)
The sampling speed is limited by the number of channels used when data is saved in the CSV format.
* When captured data is saved to the built-in RAM or SSD, data cannot be saved on the PC in real time.
Displayed information Analog waveform, Logic waveform, Pulse waveform, Digital values
Display mode Y-T waveform with digital values, XY graph in real time/replay saved data (ver. 1.20 or later), FFT measurement (ver. 1.20 or later), Cursor information, Capture condition, Alarm information
Measuring condition setting list (*20)
Content: channel number, line color, annotation, input type, measuring range, filter, unit, span, scaling
Function: Output in CSV format, Link to detailed setting
File operation Converts binary data to the CSV data (specific period, all data in one file, multiple files), Creates a new file with compression or by consolidating multiple files.
Warning Function Send e-mail to the specified address when the alarms occur
Statistical calculation Capturing data: Maximum, Minimum, Peak or Average
Replaying data: Maximum, Minimum, Peak, Average or RMS in between cursors
Search function Level Specific level in any channels
Alarm Occurred alarm in any channel
Time Beginning, center, end of the data, Trigger point, Specific time (absolute, relative), Specific number
Cursor synchronization (*20) Synchronizing cursor position on multiple screens displaying different data file
From the beginning: Synchronize the cursor position from the beginning of each screen
Position from present: Synchronize from the current cursor position of each screen
Release of remote lock of GL7000 (*20) It allows to make setting operation using control panel on GL7000 even when GL7000 is under the control of software.
Operation lock Operation screen can be locked (It is unlocked with a password.)
FFT analysis function
(Firmware ver. 1.20 or later)
Analyzing frequency range 0.08, 0.2, 0.4, 0.8, 1.6, 2, 3.2, 4, 8, 20, 40, 80, 200, 400, 800 Hz, 2, 4, 8, 20, 40, 80, 200, 400 kHz
Number of points 500, 1000, 2000, 4000, 10000
Window function Rectangular, Hanning, Hamming, Blackman, Flat-top, Exponential
Averaging Summation average, Exponential average, Peak hold
Channels 4 channels
Functions Y-T, Linear, Power, PSD, Cross, Transfer function, Coherence, COP
Display mode Single display, Dual display, Nyquist
Data recording destination selection (*20) Selecting to record data to GL7000 only or PC together with GL7000
Creating output data function
(Version 1.40 or later)
Saved data file (GBD/CSV format) in the PC, Saved data file (GBD format) in the GL7000, Generated simple waveform (DC voltage and sine, triangle, ramp, pulse waveform)
* This function is available when the analog voltage output module (GL7-DCO) is attached to the GL7000. The signal is output from the GL7-DCO module.
(*19)
When data destination is specified to the RAM or SSD on the GL7000, the captured data can not be saved on the PC in real-time. The data in the RAM or SSD on the GL7000 can be saved to the PC after the data capturing is completed.
(*20)
Supports only GL7000 with farmware version 2.0 or later & GL-Connection version 2.2 or later.

Display module GL7-DISP (option) specification

Item Description
Model number GL7-DISP
Display device 5.7-inch TFT color LCD monitor (VGA: 640 x 480 dots)
Operation Touch panel and Cursor keys (*21)
Touch panel Capacitive type touch panel, Operated by finger or the proprietary pen
Displayed language English, French, German, Chinese, Korean, Japanese
Screen saver Turns off back-light by 10, 30 sec., 1, 2, 5, 10, 30, 60 min.
Displayed information Waveform in Y-T with digital values, Waveform only, Digital value, Waveform in XY
Connection cable LAN cable (CAT5 class, Straight connection, Up to 10 m) (*22)
Standard accessories Bracket for slanted mount, Connection cable (40 cm), Ground cable, Screws
External dimensions (W x D x H) Approx. 187 x 34.5 x 119 mm (Excluding projection)
Weight Approx. 530 g
(*21)
Most operations can be selected by both the touch panel and the cursor keys.
(*22)
When the display module is mounted at an angle using the bracket, the display module is connected to the main module by a LAN cable that is attached to the display module as a standard accessory.

SSD module GL7-SSD (option) specification

Item Description
Model number GL7-SSD
Storage device Solid state disk (SSD)
Capacity (*23) Approx. 128GB (The file size of the recorded data is limited up to 4GB.)
Sampling speed (*24)(*25) Attached to 1 or 2 modules Max. 1 M Sample/s (1 ƒΚs)
Attached to 3 or 4 modules Max. 500 k Sample/s (2 ƒΚs)
Attached to 5 to 10 modules Max. 200 k Sample/s (5 ƒΚs)
External dimensions (W x D x H) Approx. 49 x 136 x 180 mm (Excluding projection)
Weight Approx. 770 g
(*23)
Capacity of memory device may be smaller than above depending on time of production. The file for recording data is limited up to 4GB on firmware version 2.0 or later, 2GB on firmware version 1.6 or before.
(*24)
The sampling speed in the GL7000 is limited to the faster sampling speed of attached input module. When the selected sampling speed in the GL7000 is faster than the module, the sampling is done in fastest sampling on the module. The same value is stored to the memory device in the selected sampling speed until data is renewed by the next sampling.
(*25)
When the sampling speed in the GL7000 is selected to the 1 MS/s (1 ƒΚs) or 500 kS/s (2 ƒΚs), the number of available channels in the Logic/Pulse module will be limited.

Humidity Sensor B-530 (option) Specifications

Item Description
Allowable temperature range -25 to 80Ž
Allowable humidity range 0 to 100“ RH
Relative humidity measurement accuracy }3“ RHi5 to 98“ RH at 25Žj
Method Capacitance method
Relative humidity measurement accuracy (5 to 98%) Measurement environment Measurement accuracy
0 to 10Ž }5“ RH
10 to 20Ž }4“ RH
20 to 30Ž }3“ RH
30 to 40Ž }4“ RH
40 to 50Ž }5“ RH
50 to 60Ž }6“ RH
60 to 70Ž }7“ RH
70 to 80Ž }8“ RH
* Measurement accuracy at 60Ž or more is a reference value.
Response time 15 sec. (90% response when membrance filter is installed)
Sensor output 0 to 1 VDC
External dimensions Dia 14 mm x length 80 mm (excluding cable)
Cable length 3 ‚
Sensor power source DC + 5 to +16 V
Power consumption approx. 4 mA

Options & accessories

@
Item Model Number Description
Sync. Cable B-559 1 m long, Synchronizing between GL7000
Carrying tool B-585 Can carry GL7000 with up to 3 modules attached.
(GL7000 + 3 modules OR GL7000 + 2 modules & SSD)
Storage case B-586 Can store GL7000 with up to 3 modules.
(GL7000 + 3 modules OR GL7000 + 2 modules & SSD)
Not for transferring. The caster can work only on smooth surface.
Probe set for Logic input RIC-10A For Logic/Pulse module (GL7-L/P), 4 channels, Cable with Alligator clip and IC clip
Input cable, BNC - BNC RIC-112 1.5 m long, Max. 60 V DC
Input cable, Banana - BNC RIC-113 1.5 m long, Max. 60 V DC
Input cable, Alligator clip - BNC RIC-114 1.5 m long, Max. 60 V DC
Input cable, Safe probe - BNC RIC-141A Insulated, 1.2 m long, 300 V DC, CAT II
Input cable, BNC - BNC RIC-142 Insulated, 1.5 m long, 1000 V DC, CAT II
Input cable, Banana - BNC RIC-143 Insulated, 1.6 m long, 600 V DC, CAT II
Input cable, Banana - BNC RIC-147 Insulated, 1.6 m long, 1000 V DC, CAT II
Clip, Alligator (small size) (*26) RIC-144A For RIC-143/RIC-147, Aperture 11 mm, 300 V DC, CAT II, Max. 15 A
Clip, Alligator (middle size) (*26) RIC-145 For RIC-143/RIC-147, Aperture 20 mm, 1000 V DC, CAT II, Max. 32 A
Clip, Grabber (*26) RIC-146 For RIC-143, Aperture 5 mm, 1000 V DC, CAT III, Max. 1 A
Input/Output cable for GL B-513 2 m long, Bare wire for signal connection - Connector for GL series
Humidity sensor (*27) B-530 3 m cables for signal and power
Shunt resistance B-551 250 ohms (Converts signal from "4-20mA" to "1-5V".)
Input connector, screw terminal B-560A For DC Strain module (GL7-DCB), Screw terminal for
sensor - D-SUB (rectangular connector) for GL7-DCB module
* Terminal holding bracket B-560AP included
Terminal holding bracket B-560AP For replacement use for B-560/B-560A
Extension cable B-560-05 For B-560/B-560A, 500 mm long
Input cable, NDIS - D-SUB B-561 For DC Strain module (GL7-DCB), NDIS (round connector) for
sensor - D-SUB (rectangular connector) for GL7-DCB module
Output cable, BNC - SMA B-562 For Voltage Output module (GL7-DCO), 2 m long,
BNC (pulg) for output - SMA (plug) for GL7-DCO module
(*26)
Red and black (per 1 unit). Connectable with RIC-143, RIC-147.
(*27)
Measurable temperature range: -25 to 80Ž

Dimensions

GL7000 Main module

GL7000 Main module with four input/output modules and SSD module

GL7000 Main module with ten input/output modules and SSD module

*
Scale : mm
Tolerance : ± 3 mm

Display module

*
Scale : mm
Tolerance : ± 3 mm

Input / Output Module

SSD module (GL7-SSD)

Voltage module (GL7-V)

Voltage/Temperature module (GL7-M)

Hi-speed Voltage module (GL7-HSV)

High Voltage module (GL7-HV)

DC Strain module (GL7-DCB)

Charge module (GL7-CHA)

Logic / Pulse module (GL7-L/P)

Voltage Output module (GL7-DCO)

*
Scale : mm
Tolerance : ± 3 mm